Факультет інженерно-технологічний
Постійне посилання на фонд
Переглянути
Перегляд Факультет інженерно-технологічний за Назва
Зараз показуємо 1 - 20 з 2233
Результатів на сторінці
Налаштування сортування
Публікація A mechanized assembly for erecting soil-cement barriers to protect agricultural lands from low-active waste during flood(2024) Петраш, Олександр Васильович; Petrash, O. V.; Zotsenko, V.; Петраш, Руслан Васильович; Petrash, R. V.; Попович, Наталія Миколаївна; Popovych, N. M.; Рожко, Ілона Іванівна; Rozhko, I. I.; Danova, K.; Malysheva, V.; Nikitchenko, O.; Nikitchenko, O.; Moroz, M.; Bogatov, O.The object of this study is the process of constructing a waterproof underground barrier from local soil using loess loam and medium-sized sand as an example. The values of waterproofing of soil cements on different types of soil and the norms of net labor consumption corresponding to them were obtained. The research solves the task of protecting agricultural lands in the areas of geological burials of low-level radioactive waste. Configuration of a mechanized drilling mixing assembly for installing a waterproof barrier in the field has been proposed. Waterproofness of soil cement on clay and sandy soils was determined experimentally. The corresponding norms of the net consumption of time for manufacturing the barrier in these soils have been determined. Units of the mechanized assembly are repairable, utilize widely available materials, parts, and mechanisms. As a result of studies on the labor intensity of the installation of soil cement, a net labor rate was established, which varies from 35 to 52 min/m3 depending on the type of soil. The corresponding values of waterproofness, which ranged from W6 to W14, were determined, which substantiates the possibility of effective functioning of soil-cement underground barriers. Options for the structural solution for impenetrable barriers have been offered. The values of the obtained net time rates are explained by the high degree of mechanization of the technological process and the use of local materials. A distinctive feature of the results is the emphasis on the data collection on the time consumption of machines and mechanisms, the characteristics of local soils under production conditions, and the use of local materials. The assembly implies using affordable and repairable units that can be serviced right in the field. Given this, the manufacturability of the proposed process was defined, confirmed by time-keeping studies. The realm of practical application of the reported results are sites within flat areas with sandy or loess bases. Barrier solutions are designed exclusively for geological waste storage facilities under the conditions of a high level of groundwater and the presence of a waterproof layer at the base.Публікація Advanced technologies in mechanical engineering(2026-02-05) Левченко, Юлія Вікторівна; Levchenko, Yu. V.; Прілєпо, Наталія Володимирівна; Priliepo, N. V.; Попов, Станіслав Вячеславович; Popov, S. V.; Петраш, Олександр Васильович; Petrash, O. V.The textbook outlines the main provisions related to the introduction of advanced technologies in the mechanical engineering. The concepts of the production process and the quality of equipment are defined. The method of designing technological processes is presented. The technological features of the production of blanks and parts by casting and plastic deformation are noted. For students majoring in Mechanical Engineering, Automobile transport, Agricultural Engineering, Vocational Education at higher education institutions, as well as professionals in manufacturing engineering for advanced training.Документ An analytical solution to the problem of thermoelastic bending of a multilayer beam with different temperature of longitudinal faces(2021-06) Ковальчук, Станіслав Богданович; Горик, Олексій ВолодимировичДокумент Analiza wybranych wyników badań instalacji solarnych w laboratorium OŹE w Zespole Szkół Elektrycznych nr 1 w Krakowie oraz Połtawskiej Państwowej Akademii Rolniczej(2010) Tytko, R.; Brykun, O. M.; Брикун, Олександр МиколайовичДокумент Analytical Determination of Reactive Forces for Curvilinear Bars with a Flat Axis of Arbitrary Shape / Аналітичне визначення реактивних зусиль для криволінійних брусів із плоскою віссю довільної форми(2019-12) Ковальчук, Станіслав Богданович; Горик, Олексій ВолодимировичДокумент Analytical Modeling of Concentrated and Localized Loads of Bars With a Curvilinear Flat Axis. Part 2. Modeling Localized Loads and Application Examples / Аналітичне моделювання зосереджених та локалізованих навантажень брусів із криволінійною плоскою віссю. Частина 2. Моделювання локалізованих навантажень та приклади застосування(2019-09) Ковальчук, Станіслав БогдановичДокумент Analytical Solution of the Problem of Thermoelastic Deformation of a Nonuniformly Rotating Multilayer Disk(2020-03) Ковальчук, Станіслав Богданович; Горик, Олексій Володимирович; Зiньковський, Анатолiй ПавловичДокумент Analytical Solution to the Plane Bending Task of the Multilayer Beam with a Circular Axis under Normal Uniform Loading(2020-09) Ковальчук, Станіслав БогдановичДокумент Application of tne fish search algorithm for optimization plans of the full factor experiment(IEEE Operations Center 445 Hoes Lane,P.O. Box 1331, Piscataway, NJ 08855-1331 USA, 2018) Muratov, V. ; Koshevoy, M.; Kostenko, O. M.; Костенко, Олена МихайлівнаA method and program was developed to optimize the plans for a full factorial experiment using the search algorithm for fish. A comparative analysis of methods for the synthesis of optimal full-scale experiment experiments for cost and time costs has been carried out. The efficiency of the method was tested on a number of such technological objects: fuel consumption in the internal combustion engine, welding of thin plates, production of parts by hot stamping, and also the process of servicing machines with numerical control. The effectiveness of the method of searching for fish by the school is shown.Документ Assessment of the danger of using ultraviolet lamps in electrical systems(2024) Semenov, A. O.; Popov, S. V.; Yakhin, S. V.; Yeleussinov, B.; Sakhno, T. V.; Семенов, Анатолій Олексійович; Попов, Станіслав Вячеславович; Яхін, Сергій Валерійович; Сахно, Тамара ВікторівнаTo determine the photobiological safety of UV lamps, the following measurements were carried out: spectral irradiance, total actinic irradiance in the wavelength range of 200-400 nm, and irradiance in the UVA range (320-400 nm). These parameters were measured using the optical radiation system OST-300. The photobiological safety of LUF 40-1, LE 15 lamps and their radiation risk group are established in accordance with EN 62471. The levels of UV radiation generated by LE 15 low pressure discharge lamps at a distance of 0.25 m belong to the high risk group (GR3), and LUF 40-1 - in the group of insignificant risk (GR1). Calculations and recommendations on safe radiation doses when using lamps in electrotechnical systems of photobiological influence are given.Документ Bactericidal Disinfection of Activated Carbon from Aerobic Microorganisms, Yeasts and Molds(2022-02) Semenov, A. O. ; Sakhno, T. V.; Hmelnitska, Y. V.; Semenova, N.; Семенов, Анатолій Олексійович; Сахно, Тамара Вікторівна; Хмельницька, Євгенія ВікторівнаДокумент Basic Stress-Strain State of a Multilayer Circular Ring under the Action of Mutually Opposite Normal Forces / Основное напряженно-деформированное состояние многослойного кругового кольца под действием взаимно противоположных нормальных сил(2019-03) Ковальчук, Станіслав Богданович; Горик, Олексій ВолодимировичДокумент Basic Stress-Strain State of a Multilayer Symmetric Circular Arch under the Action of Normal Forces in the Middle Section. Report 1. Arches of High Curvature / Аналітичний розв’язок задачі згину багатошарової симетричної кругової арки під дією нормальної сили у середньому перерізі. Повідомлення 1. Арки великої кривизни(2019-06) Ковальчук, Станіслав Богданович; Горик, Олексій ВолодимировичДокумент Bimetallic Temperature Sensors(2019) Koshevoy, M. ; Koshevaya, I.; Fesenko, A.; Kostenko, O. M.; Костенко, Олена МихайлівнаДокумент Building an analytical model of the gravitational grain movement in an open screw channel with variable inclination angles(2021-07-01) Арендаренко, Володимир Миколайович; Антонець, Анатолій Вікторович; Іванов, Олег Миколайович; Дудніков, Ігор Анатолійович; Самойленко, Тетяна ВолодимирівнаДокумент Classification rule for determining the temperature regime of induction gray cast iron(2021-01-30) Stanovska, Iraida; Duhanets, Vasyl; Prokopovych, Lada; Yakhin, S. V.; Яхін, Сергій ВалерійовичДокумент Combined method of UV treatment and ozonation during water disinfection in swimming pools(2021-11) Semenov, A. O. ; Vyzhva, S.; Sakhno, T. V.; Semenova, N.; Семенов, Анатолій Олексійович; Сахно, Тамара ВікторівнаПублікація Conductive frying of meat:current state and prospects(2025-12-18) Скрипник, Вячеслав Олександрович; Skrypnyk, V. O.; Yeleussinov, B.; Семенов, Анатолій Олексійович; Semenov, A. O.The monograph analyzes the current state of processes and equipment for conductive meat frying. A methodology for evaluating the energy and resource efficiency of meat frying processes and equipment has been developed. Based on this methodology, potential directions for improving the energy and resource efficiency of these processes and devices have been identified. A scientific concept is proposed, which involves creating conditions for intensified heat transfer during conductive frying by employing various physical and electrophysical methods—such as the application of electric current combined with compression, compression in a functionally closed volume, or in functionally closed chambers. The concept is supported by research results obtained from experimental prototype devices. The monograph is intended for academic staff, postgraduate and master's students, researchers, and professionals in the field of food production.Документ Cилос зі спіральним завантажувачем з неоднорідним покриттям поверхні спуску(Український інститут інтелектуальної власності, 2021-05-12) Іванов, Олег Миколайович; Арендаренко, Володимир Миколайович; Савченко, Назарій Константинович; Сімонов, Кирило ВікторовичСилос зі спіральним завантажувачем з неоднорідним покриттям поверхні спуску, до складу якого входить циліндрична ємність із завантажувальним патрубком, який переходить у відкритий гвинтовий канал, спрямований до низу силоса та утворений провертанням U-подібного профілю за гвинтовою лінією, який відрізняється тим, що поверхня гвинтового каналу по всій довжині спуску розділена на три рівні частини з нанесеним окремо на кожну покриттям з різними трибологічними властивостями, при цьому для кожної нижчерозташованої частини поверхні гвинтового каналу величина контактної взаємодії з зерном зростає.Документ DEFINING THE PARAMETERS FOR A BRUSH WITH POLYPROPYLENE BRISTLE WHEN UNCOVERING THE ROOT SYSTEM OF MATERNAL PLANTS(2019-08) Іванов, Олег Миколайович; Харак, Руслан Миколайович; Пушка, Олександр СергійовичРозглянуто питання роботи циліндричної щітки з гнучкими прутками ворсу при розкритті кореневої системи маточних рослин. Встановлено, що основними складовими сили опору при роботі даної щітки є сума опорів, що спричинені силою в’язкості ґрунту, силою статичного опору сипучих частинок ґрунту та силою опору відкидання частинок ґрунту. Виходячи з мінімізації затрат енергії, визначено оптимальні кінематичні параметри щітки з вертикальною віссю обертання. Великий влив на значення загальної сили опору має кутова швидкість щітки. Крім сили опору на прутки ворсу щітки діє нормальна реакція ґрунтової основи. Знайшовши результуючу цих двох сил за допомогою методу еліптичних інтегралів Лежандра, встановлено оптимальні розмірні параметри прутків ворсу, що виготовлені з поліпропілену. Даний метод дозволив врахувати значні, у порівнянні з довжиною прутків, їх деформації в результаті їх згину. Довжина прутків визначена як максимально можлива для забезпечення умови видалення ґрунту з валка, що вкриває кореневу систему маточних рослин клонових підщеп. Також досліджено вплив сили тертя під час роботи щітки. Це тертя частинок ґрунту між собою та по поверхні прутків ворсу. Визначено, що сили тертя, як нормальна реакція ґрунту, мало впливають на роботу циліндричної щітки при розкритті кореневої системи маточних рослин. Це пояснюється відсутністю твердої основи при роботі прутка ворсу, що в свою чергу дозволяє розміщувати прутки ворсу по одному на поверхні щітки. Відсутність потреби у значній відносній жорсткості дозволяє пруткам ворсу видаляти ґрунт з валка мінімізуючи при цьому пошкодження рослин. За допомогою еліптичних інтегралів Лежандра другого роду досліджено прогин прутків ворсу циліндричної щітки при розкритті кореневої системи маточних рослин. Величина прогину прутка в процесі роботи впливає на повноту видалення ним частинок ґрунту. При збільшення прогину змінюється кут між робочою гранню прутка ворсу і поверхнею ґрунту. Це призводить до зменшення видалення частинок і збільшення їх ущільнення у валку. Тому розрахована довжина прутків ворсу, які здатні забезпечити необхідні робочі параметри при заданому навантаженні.